Lanner LEC-3000A User Manual

>>Embedded & Industrial ComputingHardware Platforms for Embedded and Industrial ComputingLEC-3000AUser's ManualPublication date:2011-0

8Motherboard InformationChapter 3Embedded and Industrial ComputingMotherboard LayoutThe motherboard layout shows the connectors and jumpers on

9Motherboard InformationChapter 3Embedded and Industrial ComputingRear Side of the Main BoardDC/DC converter board41.625.69989.27Board dimension unit

10Motherboard InformationChapter 3Embedded and Industrial ComputingJumper SettingsSATA1: The system supports one SATA II drive SO-DIMM1: The SO-DIMM

11Motherboard InformationChapter 3Embedded and Industrial ComputingSW2/SW3/SW4/SW5: These switches — SW2, SW3, SW4 and SW5 — are used to adjust

12Programming Watchdog TimerEmbedded and Industrial ComputingAppendix AAppendix A: Programming Watchdog TimerA watchdog timer is a piece of ha

13Programming Watchdog TimerEmbedded and Industrial ComputingAppendix AChoose to select the hardware Manually8. Choose Show all device and click Next.

14Programming Watchdog TimerEmbedded and Industrial ComputingAppendix ASelect the Lanner IO driver and click Next.14. Click Next15. Click 16. Complet

15Programming Watchdog TimerEmbedded and Industrial ComputingAppendix AWatch Dog sample code:// LEC3000_Test.cpp : Defines the entry point for the con

16Programming Watchdog TimerEmbedded and Industrial ComputingAppendix A Run_LED (0, 0) ; Run_LED (1, 0) ; } else if (argv[1][0] == ‘3’)

17Digital Input/Output ControlAppendix BEmbedded and Industrial ComputingAppendix B: Digital Input/Output Control on the GPIO portThe Digitanl I/O on

TTaTTable of Contentsbeable of ContentsiChapter 1: Introduction 1System Specication . . . . . . . . . . . . . . . . . . . . .

18Digital Input/Output ControlAppendix BEmbedded and Industrial ComputingChoose to select the hardware Manually8. Choose Show all device and click Nex

19Digital Input/Output ControlAppendix BEmbedded and Industrial ComputingSelect the Lanner IO driver and click Next.14. Click Next15. Click 16. Compl

20Digital Input/Output ControlAppendix BEmbedded and Industrial ComputingA DIO sample code: // LEC3000_Test.cpp : Defines the entry point for

21Digital Input/Output ControlAppendix BEmbedded and Industrial Computing Sleep (1) ; } Run_LED (0, 0) ; Run_LED (1, 0) ; } els

22Driver InstallationAppendix ENetwork Application PlatformsAppendix E: Driver InstallationLAN Adapters Driver InstallationThis section provides

23Driver InstallationAppendix ENetwork Application PlatformsLinuxFollow these instructions to install the Realtek® LAN controller base driver

24Terms and ConditionsAppendix DEmbedded and Industrial ComputingAppendix D: Terms and ConditionsWarranty Policy All products are under warran

25Terms and ConditionsAppendix DEmbedded and Industrial ComputingRMA Service Request Form When requesting RMA service, please fill out the following

1IntroductionChapter 1Embedded and Industrial ComputingChapter 1: IntroductionThank you for choosing the LEC-3000A. The LEC-3000A is an embedded aut

2IntroductionChapter 1Embedded and Industrial ComputingPackage ContentsYour package contains the following items:LEC-3000A Embedded System •Din-Rail M

3IntroductionChapter 1Embedded and Industrial ComputingF1 VGA PortUsing suitable DB-15 cable, you can connect an appropriate device such as a monitor

4IntroductionChapter 1Embedded and Industrial ComputingTop and Bottom Panel FeaturesR1 Reset Switch: A hardware reset switch Use a pointed object to

5IntroductionChapter 2Embedded and Industrial ComputingChapter 2: Hardware SetupPreparing the Hardware InstallationTo access some components and perf

6IntroductionChapter 2Embedded and Industrial ComputingConnecting PowerConnect the LEC-3000A to a 12~36 VDC power source. The power source comes from

7Motherboard InformationChapter 3Embedded and Industrial ComputingChapter 3: Motherboard InformationBlock DiagramThe block diagram depicts the r