Network Application PlatformsHardware platforms for next generation networking infrastructureFW-8894V1.0User's ManualRelease Date: 2015/02/09
Chapter 2: Motherboard InformationBlock DiagramThe block diagram indicates how data flows among components on the motherboard. Please refer to the fo
Motherboard LayoutThe motherboard layout shows the connectors and jumpers on the board. Refer to the following picture as a reference of the pin assig
Internal Jumper & ConnectorsJLCM1: USB-type front LCD Message Display Module (LCM). MGT1: RJ 45 LAN management port connector by Intel I210 LANM
JFAN1~4: 5-Pin FAN Connector. J27: Jumper for Reset JUSB1: USB 2.0 internal pin headerPin Description1 Ground2 12V3 RPM Sense4 RPM Sense5 PWM Status
OPMA1: OPMA interface. The OPMA connector is for connecting the OPMA card. When the OPMA card is connected, the management port will comply with the
J23: LCMCON3: PMBUS/TTLJOPEN1: Chassis Open Detect mainboard protection jumper. (a short-pin cap will be connected to the top compartment of the syste
Chapter 3: Hardware SetupPreparing the Hardware InstallationWARNING: To reduce the risk of personal injury, electric shock, or damage to the equipmen
4. Open the load plate and also the protective cap.5. Align the CPU and the notch on the socket. The CPU should fit perfectly into the socket. Note th
Installing the System Memory The motherboard supports DDR4 registered DIMM memory for heavy-duty operations. Please follow the steps below to install
Installing the CFast CardFW-8894 provides one CFast slot. Follow the procedures below for installing a CFast card.Locate the CFast socket.1. Remove th
Table of ContentsOverview 3Chapter 1: Introduction 6System Specifications 6Package Contents 7Ordering Information 7Compatible Accessories 7Fron
4. You may adjust it to be used for 2 x 2.5” SATA HDD/SSD. Just relocate the side bracket as shown below. 5. Use SATA cables to connect your HDD/SSD
Installing the NIC ModulesFW-8894 series comes with 4 NIC Ethernet module slots for network bandwidth expansion. Please follow the steps for installat
Replacing the Power Supply UnitsPower supply units may wear down eventually. Please be noted that FW-8894 series supports 650W depending on the orderi
Rack MountingInstallation Precautions:Elevated Operating Ambient - If installed in a closed 1. or multi-unit rack assembly, the operating ambient temp
Installing the system to the rackNotes for Step 5: it is strongly recommended that installing the system onto the rack is a 2-persons' job. Pleas
Appendix A: Programming Watchdog TimerA watchdog timer is a piece of hardware that can be used to automatically detect system anomalies and reset the
Appendix C: Programming Generation 3 LAN BypassThe bypass function is used to link two independent Ethernet ports when the system crashes or powers
Appendix D: Programming the LCMThe LCD panel module (LCM) is designed to provide real-time operating status and configuration information for the sys
Corresponding Commands for plcm_test You can directly input the specic command to have its corresponding function worked on your LCM. Thiswill be muc
(3) Open a terminal in the Guest OS and then issue the following commands to install linux kernel drivers.# modprobe parport# modprobe parport_pc# mod
OverviewIcon DescriptionsThe icons are used in the manual to serve as an indication of interest topics or important messages. Below is a description
Appendix E: On LinuxFollow these instructions when installing the Intel® LAN controller base driver for the in Red Hat® and Linux operating system. I
Appendix F: Terms and ConditionsWarranty Policy All products are under warranty against defects in 1. materials and workmanship for a period of one
EMC NoticeThis equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These
Revision HistoryVersion Date DescriptionsV1.0 2015/02/09 Ocial release
Chapter 1: IntroductionThank you for choosing Lanner FW-8894. The FW-8894 is the 1U version of our already launched powerful platform of FW-8896. I
Package ContentsYour package contains the following items:FW-8894 Network Security Platform•2 power cables•1 Long Ear Rack mount kit with screws•1
Front Panel Features F1 Power/Status/HDD LEDPower LED: If the LED is on, it indicates that the system is powered on. If it is off, it indicates that
Rear Panel Features R1 4 x Cooling fansR2 Power switchR3 Power supply units for RPS (Redundent Power Supply)R3R1R2
Comments to this Manuals